Chrysler 200 Forum banner

1 - 20 of 25 Posts

·
Registered
Joined
·
202 Posts
Discussion Starter #1 (Edited by Moderator)
Upon recent request, some members have been asking me to create a list of the LED's I have used in my car. Below is a list of each light, and the replacement LED (can be found in link). Hope this helps out some of the newbies. If any other members would like to add to the list please PM me and I'll add it. These LED's can be purchased through other vendors, however I can not vouch for how they work. I've only attached links to the places I have ordered from. Most of which are very good suppliers.



Headlights - Stock HID D3S (4300K)

http://www.theretrofitsource.com/components/bulbs/new-philips-ultinon-flash-white-6000k-d3s-bulbs.html#.VXV6Ks9VhBc

http://www.theretrofitsource.com/components/bulbs/d3s-osram-xenarc-66340-cbi-49205.html#.VXV6K89VhBc

http://www.theretrofitsource.com/components/bulbs/morimoto-xb-d3s-bulbs.html#.VXV6Ns9VhBc

(link for install)
http://www.200forums.com/forum/66-2015-chrysler-200-uf-appearance-body/25841-how-hid-replacement.html



Headlights - Stock HIR2 (Bi-Halogen)

(HID Swap)
http://www.theretrofitsource.com/hid-systems/morimoto-elite-hid-system-15-dodge-ram-low-beam.html#.VXcld89VhBd

(link to thread with info)
http://www.200forums.com/forum/66-2015-chrysler-200-uf-appearance-body/31370-plug-n-play-hid-2015-chrysler-200-a.html



Front Turn Signal - Stock PWY24W SV (Amber Incandescent)

I have not found a suitable LED for this. I've tried a few, however none of which have been brighter than the stock bulb.



Side Marker - Stock 194 (Amber Incandescent)

(select amber when purchasing)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb-5-smd-led-wide-angle-wedge-base/206/



Front Fog Lamp - Stock H11 (Incandescent)

(supplier website)
http://www.usa.philips.com/c-p/12834UNIX2/x-treme-ultinon-led-car-lamp

(link for install)
http://www.200forums.com/forum/66-2015-chrysler-200-uf-appearance-body/26618-how-replace-led-fog-lights.html



Stop/Turn Signal - Stock 7440 (Incandescent)

(select 7440, you do not need resistors)
http://www.vleds.com/v3-r.html

(link for install)
http://www.200forums.com/forum/66-2015-chrysler-200-uf-appearance-body/26306-how-brake-light-led-conversion.html



Backup - Stock 921 (Incandescent)

(select cool white)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb--19-smd-led-wedge-base-tower/1563/

(link for install)
http://www.200forums.com/forum/66-2015-chrysler-200-uf-appearance-body/26314-how-reverse-light-led-conversion.html



License Plate - Stock 194 (Incandescent)

(select cool white)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb-5-smd-led-wide-angle-wedge-base/206/



Front Courtesy - Stock 194 (Incandescent)

(select cool white)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb-5-smd-led-wide-angle-wedge-base/206/

(link for install)
http://www.200forums.com/forum/82-2015-chrysler-200-uf-interior/26882-how-front-interior-led-light-conversion.html



Rear Courtesy - Stock LED (Panoramic Version)

(select cool white/black)
https://www.superbrightleds.com/moreinfo/led-wired-bolts/plm-series-wired-one-and-half-watt-led/1141/2797/

(link for install)
http://www.200forums.com/forum/82-2015-chrysler-200-uf-interior/26530-how-rear-interior-led-conversion-sunroof-version.html



Rear Courtesy - Stock 194 (Incandescent)

(select cool white)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb-5-smd-led-wide-angle-wedge-base/206/



Visor/Vanity - Stock A6220 (Incandescent)

(link may fail over time, search for any T5 side emitting LED)
http://www.amazon.com/Amico-White-1210-Light-Wedge/dp/B00AKXBQAU/ref=sr_1_3?s=automotive&ie=UTF8&qid=1433763555&sr=1-3&keywords=t5+led



Glove Box - Stock 194 (Incandescent)

(select cool white)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb-5-smd-led-wide-angle-wedge-base/206/



Trunk - Stock 194 (Incandescent)

(select cool white)
https://www.superbrightleds.com/moreinfo/miniature-wedge-base/194-led-bulb-5-smd-led-wide-angle-wedge-base/206/

For even brighter and more lit trunk use the below led strip

(select cool white/39.4"/Black)
https://www.superbrightleds.com/moreinfo/top-emitting/led-light-strips-led-tape-light-with-18-smdsft-3-chip-smd-led-5050-with-lc2-connector/1465/

(link for install)
http://www.200forums.com/forum/82-2015-chrysler-200-uf-interior/25602-led-trunk-light-floor-liner-installed.html
 

·
Premium Member
Joined
·
1,397 Posts
Sticky'd!

EDIT: Wait actually not yet. I think you couldn't edit it because it was a sticky. Let me know when you're done editing and I'll stick it again!
 

·
Registered
Joined
·
202 Posts
Discussion Starter #4
Thanks!
 

·
Registered
Joined
·
24 Posts
Sorry if this is asked a lot of times, but I'm new to converting to LEDs. But for the most part it's just plug 'n play, right? The license plate lights for example. I've got the 200 limited without the lighting package so I just want to be 100% on something before I upgrade anything.
 

·
Super Moderator
Joined
·
1,820 Posts
Sorry if this is asked a lot of times, but I'm new to converting to LEDs. But for the most part it's just plug 'n play, right? The license plate lights for example. I've got the 200 limited without the lighting package so I just want to be 100% on something before I upgrade anything.
Licence plate is plug and play, so is trunk, glove box and H11 fog lights. As far as headlights are concerned it might be tricky althouh the link provided for HID conversion is pretty much plug and play.

Interior lights are pretty easy if you don't have a sunroof, but it a whole different ball game if you have the sunroof.
 

·
Registered
Joined
·
24 Posts
Licence plate is plug and play, so is trunk, glove box and H11 fog lights. As far as headlights are concerned it might be tricky althouh the link provided for HID conversion is pretty much plug and play.

Interior lights are pretty easy if you don't have a sunroof, but it a whole different ball game if you have the sunroof.

Thanks so much. I won't be upgrading the headlights or tails for a little while, but I want to make the interior a little brighter and I do not have a sunroof and I feel like it's a great place to start.
 

·
Registered
Joined
·
202 Posts
Discussion Starter #8
Most are plug and play. Some of them have links to other threads that explain how to install. Most of them have been explained in other threads. If you have any questions feel free to PM me.
 

·
Registered
Joined
·
202 Posts
Discussion Starter #11
Just to bring this back from the dead, anybody thought about running an amber drl/turn signal? Would this work?

http://www.ebay.com/itm/No-Error-PWY24W-Amber-SAMSUNG-LED-Turn-Signal-Daytime-Running-Light-Audi-BMW-F30-/360880736558
DO NOT WASTE YOUR MONEY ON THOSE!!!!


I am speaking from personal experience. I bought those awhile ago and put one on. I kept the passenger side stock so I could see a side by side comparison. That LED is no where near as bright as the factory incandescent bulb.
 

·
Registered
Joined
·
202 Posts
Discussion Starter #13

·
Registered
Joined
·
59 Posts

·
Registered
Joined
·
15 Posts
Front Turn Signal - Stock PWY24W SV (Amber Incandescent)
I have not found a suitable LED for this. I've tried a few, however none of which have been brighter than the stock bulb.

--------------------------------------------------------------------
My dear friend and others too... try this bulb from Ebay: http://www.ebay.com/itm/161631628073?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT

I found it bright and very nice looking for our 2015-2016 (chrysler 200). It is a canbus free and does not need any other thing.
 

·
Registered
Joined
·
15 Posts
Stop/Turn Signal - Stock 7440 (Incandescent)

(select 7440, you do not need resistors)
http://www.vleds.com/v3-r.html
(link for install)
http://www.200forums.com/forum/66-2015-chrysler-200-uf-appearance-body/26306-how-brake-light-led-conversion.html
------------------------------------------------------------------------------------------------------------------------------------------------

try this for the rear break/signal bulb: http://www.ebay.com/itm/161763164206?_trksid=p2057872.m2749.l2649&ssPageName=STRK:MEBIDX:IT

it does not need resistor and it is plug&play with bright full reflection. I like it.
 
1 - 20 of 25 Posts
Top