[Silver Streak]

I was wondering if the 2015 200S and 200C models are pre-wired for the "Driver Memory Seat" switch behind the door panel? My 200S AWD/U-Connect 8.4AN doesn't have that option, but it does have the dual power/ventilated seats.

If all it takes is the installation of the 3 position switch in the drivers door and perhaps some additional programing I'd like to have that additional choice.

Thanks!

 

[Spec]

You ever figure this out? I have a 200 Limited with powered driver seat and want to install this

 

[200_S_AWD]

It isn't plug n' play. Some hardware & software is different. The 'sales code': LEZ would have to be entered & accepted in the BCM. The door & seat wiring harnesses are different. You would want to find a donor 200 w/memory for the parts car.
The door trim panel switches, body wiring & seat modules are different.
It would be a big project, but it would probably be possible.

 

[Spec]

It isn't plug n' play. Some hardware & software is different. The 'sales code': LEZ would have to be entered & accepted in the BCM. The door & seat wiring harnesses are different. You would want to find a donor 200 w/memory for the parts car.
The door trim panel switches, body wiring & seat modules are different.
It would be a big project, but it would probably be possible.
View attachment 62294
View attachment 62295
View attachment 62296

Thanks for the reply. I figured I needed to do some programming but not all this wiring. I probably won’t tackle this project, as the results aren’t really worth all the time and struggles lol.

 

[200_S_AWD]

If it was a 'his & hers' sharing of the car, I might see memory settings as a useful option. If you are the primary driver of the car, not so much. I just set my seat & mirrors and forget it, unless someone sits behind me.

 

[kdt1970]

I wish I had it in mine, I can't count how many times I have been crushed getting into the car after my wife has driven it and not realizing how close the steering wheel is to the seat.

 

[Spec]

I wish I had it in mine, I can't count how many times I have been crushed getting into the car after my wife has driven it and not realizing how close the steering wheel is to the seat.

Haha! I guess I am lucky where I do not need the function that bad. But I still would have liked it.

 

[Dorius]

I was wondering if the 2015 200S and 200C models are pre-wired for the "Driver Memory Seat" switch behind the door panel? My 200S AWD/U-Connect 8.4AN doesn't have that option, but it does have the dual power/ventilated seats.

If all it takes is the installation of the 3 position switch in the drivers door and perhaps some additional programing I'd like to have that additional choice.

Thanks!

If you independently redo the driver seat, then this is a large amount of work with wiring.
Motors in the seat with memory are 4 pin, not 2 pin on power seat (or power seat + ventilation).

It is easier to replace the salon from the car where seats with memory.
Replace the front left card of the door with memory buttons.
Replace the mirrors from the car with the memory of the seats, there are other motors inside. Bonus from the replacement of mirrors - turn lights in the mirrors.

Since you do not have a basic 200S, there will be less work with chassis wiring. After change seats you need to add + and - to the driver chair connector.
Doors wiring is already suitable in your car, as well as door module.

Of course, you need to make changes to the settings with AlfaOBD and make PROXI alignment.

From the Ukrainian club, I know only 3 cars owners who did it.
I postponed this issue for later to do, not ready now to spend $800 on a salon with memory, and $300 for mirrors with "memory".
But when I added wiring for heated seats, I also added wiring for ventilation and memory. I have used original chassis wiring from another scrapped 200C.